|
| |
MITSUBISHI SERVO "G" MOTOR AND CONTROL BOX
|
MITSUBISHI SERVO "G" MOTOR AND CONTROL BOX |
Drive Unit
LIMISERVO XC-G series
LIMISERVO XC-G Series : Induction type AC Servo Motor
and Control Box |
|
|
| |
|
| * |
Motor size and weight reduction |
| |
*Realization of compact. lightweight
motor
Motor size reduced by approximately 60% when compared
with previous motor (XL-554). Motor weight reduced by spproximately
1.7kg. |
| * |
Enhanced functionality |
| |
*Step sequence function
-This function enables
easy programming of the desired input, output and machining
operation in sequence with the stitching process. (Extensive upgrade
of existing machine simple sequence mode)
-Various operations can
now be incorporated into the "stitching process", including those
performed before and after operation.
*Direct parameter No.
call-up function
Previously it was necessary to select the
respective mode to perform settings when making changes to the
parameters, however, by using the G10 or G500-Y control panel, it is
now possible to call up the required parameter in a single
operation. It is also possible to call up parameters for each
mode. |
| * |
User-friendly function |
| |
*Compute interface standard
equipment
-Settings data control including batch writing, reading
and saving of settings can be performed using the setup software.
(XCG_SET)
-Step sequence creation, editing, etc. can be performed
using the dedicated step sequence software. (XCG_STEP) |
| * |
Multi-function, Interchangeability |
| |
*Full functionality
-The G series retains all
the operability and multi-functionality of the XC-F series! The
control box uses the same connectors as the XC-F series, enabling
easy connection.
-The settings data save function has been
expanded to enable saving of settings data from 1 model to 2
models.
-A parameter change difference display has been added. (A
flashing dot ( . ) displays at the changed parameter.)
-2 types
of function setting can now be performeed with a single
input.
*Interchangeability
The XC-KE-01P detector,
XC-FM-2, XC-FM-3 (LS2-1380 only), and LE-FA presser foot lifter
units and XC-CVS-2 variable speed pedal can all be used as is. The
XL-554 motor can be used with an optional attachment
bracket.
*Control panel
XC-G10 and XC-G500-Y series
control panels are available. The existing operation panel can be
attached to and removed from the XC-G10 series control panel.
Significant enhancements have been made to the operability of the
XC-G500-Y series control panel over existing functionality
(XC-E500-Y), and the settings data memory has been
doubled. | |
| |
 |
|
| Type |
Motor
Connector |
Power
Supply |
Output(W) |
Output
Shaft |
Mass |
| Number of phases |
Voltage(V) |
| XL-G554-10Y |
Strain relief |
Single phase |
100 to 120 |
550 |
Taper shaft |
6.9Kg
(net)
9.1kg
(gross) |
| XL-G554-10 |
Vinyl cap |
| XL-G554-20Y |
Strain relief |
Three phases
Single
phase(*1) |
200 to 240 |
| XL-G554-20 |
Vinyl cap |
| XL-G754-20Y |
Strain relief |
750 |
| XL-G754-20 |
Vinyl cap | |
| |
| Type |
Output |
Power
supply |
Function |
Mass |
| Number of phases |
Voltage |
| XC-GMFY-10-05 |
550W |
Single phase |
100-120 |
Full functionality including auto thread
trimming, presser foot lifting, fixed-stitch stitching, continuous
stitching and backtacking. Equipped with step sequence, simple
sequence and computer communication functions (when connected to
control panel). Equipped with 8 solenoid drive outputs, 2
electromagnetic valve outputs, 1 small-signal output and 14 input
terminals including a variable voltage input. |
3.5Kg
(net)
6.9kg
(gross) |
| XC-GMFYCE-20-05(*2) |
200-240 |
| XC-GMFY-20-05 |
Three phase/
Single
phase(*1) |
| XC-GMFY-20-07 |
750W | |
Note1:Refer to the Instruction Manual for how
to connect the types marked with (*1)
Note2:Type [XC-GMFYCE] is CE
marking type (*2) |
| |
| Options |
| Control
panel |
XC-G10S [control box attachment type
(One unit is standard
equipment.)]
XC-G10L
XC-G500-Y ("XC-G500-Y"
and "XC-G10" cannot be used together.) |
| Auto
presser foot lifter unit |
XC-FM-2 : Electromagnetic type (for
24V)
XC-FM-3 : It is possible to use it for LS2-1380. (for
24V)
LE-FA : Pneumatic type (common for 30V/24V) |
| Variable
speed pedal |
XC-CVS-2 : 3-speed pedal, for standing
operation sewing machine |
| Lever unit
(separated type) |
XC-GL-1-SET : 1-step kick-back use
(installation plate, extension cable set)
XC-GL-2-SET : 2-step
kick-back use (installation plate, extension cable set) |
| Extension
cables |
Motor cable 1.0m :
K14M52158002
Detector cable 0.6m : K14M71324830
Encoder cable
1.0m : K14M71725402 |
| Installation metal fittings |
XL-G554 motor and old control box :
K14M72354001
Old motor and XC-GMFY control box :
K14M72354101 | |
| |
|
|
|
Sewing
Machine Services Luton Ltd 
